The libtool .la files are only useful when linking with static libraries. They are unneeded, and potentially harmful, when using dynamic shared libraries, specially when using non-autotools build systems. While still in chroot, remove those files now:
find /usr/{lib,libexec} -name \*.la -delete
Remove the documentation of the temporary tools, to prevent them from ending up in the final system, and save about 35 MB:
rm -rf /usr/share/{info,man,doc}/*
All the remaining steps in this section are optional. Nevertheless, as soon as you begin installing packages in Chapter 8, the temporary tools will be overwritten. So it may be a good idea to do a backup of the temporary tools as described below. The other steps are only needed if you are really short on disk space.
The following steps are performed from outside the chroot environment. That means, you have to leave the chroot environment first before continuing. The reason for that is to:
make sure that objects are not in use while they are manipulated.
get access to file system locations outside of the chroot
environment to store/read the backup archive which should not
be placed within the $LFS
hierarchy for safety reasons.
Leave the chroot environment and unmount the kernel virtual file systems:
All of the following instructions are executed by root
. Take extra care about the commands you're
going to run as mistakes here can modify your host system. Be aware
that the environment variable LFS
is set
for user lfs
by default but it
might not be set for
root
. Whenever commands are to be
executed by root
, make sure you
have set LFS
accordingly. This has been
discussed in Section 2.6,
“Setting The $LFS Variable”.
exit umount $LFS/dev{/pts,} umount $LFS/{sys,proc,run}
If the LFS partition is rather small, it is good to know that unnecessary items can be removed. The executables and libraries built so far contain a little over 90 MB of unneeded debugging symbols.
Strip off debugging symbols from binaries:
strip --strip-debug $LFS/usr/lib/* strip --strip-unneeded $LFS/usr/{,s}bin/* strip --strip-unneeded $LFS/tools/bin/*
These commands will skip a number of files reporting that it does not recognize their file format. Most of these are scripts instead of binaries.
Take care NOT to use
--strip-unneeded
on the
libraries. The static ones would be destroyed and the toolchain
packages would need to be built all over again.
At this point, you should have at least 5 GB of free space on the chroot partition that can be used to build and install Glibc and GCC in the next phase. If you can build and install Glibc, you can build and install the rest too. You can check the free disk space with the command df -h $LFS.
Now that the essential tools have been created, its time to think about a backup. When every check has passed successfully in the previously built packages, your temporary tools are in a good state and might be backed up for later reuse. In case of fatal failures in the subsequent chapters, it often turns out that removing everything and starting over (more carefully) is the best option to recover. Unfortunately, all the temporary tools will be removed, too. To avoid spending extra time to redo something which has been built successfully, prepare a backup.
Make sure you have at least 600 MB free disk space (the source
tarballs will be included in the backup archive) in the home
directory of user root
.
Create the backup archive by running the following command:
cd $LFS && tar -cJpf $HOME/lfs-temp-tools-10.1-rc1-systemd.tar.xz .
Replace $HOME
by a directory of your
choice if you do not want to have the backup stored in root
's home directory.
In case some mistakes have been made and you need to start over,
you can use this backup to restore the temporary tools and save
some recovery time. Since the sources are located under
$LFS
, they are included in the backup
archive as well, so they do not need to be downloaded again. After
checking that $LFS
is set properly,
restore the backup by executing the following commands:
cd $LFS &&
rm -rf ./* &&
tar -xpf $HOME/lfs-temp-tools-10.1-rc1-systemd.tar.xz
Again, double check that the environment has been setup properly and continue building the rest of the system.
If you left the chroot environment either to strip off debug symbols, create a backup, or restart building using a restore, remember to mount the kernel virtual filesystems now again as described in Section 7.3, “Preparing Virtual Kernel File Systems” and re-enter the chroot environment (see Section 7.4, “Entering the Chroot Environment”) again before continuing.