DHCP-4.4.2

Introduction to ISC DHCP

The ISC DHCP package contains both the client and server programs for DHCP. dhclient (the client) is used for connecting to a network which uses DHCP to assign network addresses. dhcpd (the server) is used for assigning network addresses on private networks.

This package is known to build and work properly using an LFS-9.1 platform.

Package Information

User Notes: http://wiki.linuxfromscratch.org/blfs/wiki/dhcp

Kernel Configuration

You must have Packet Socket support. IPv6 support is optional.

[*] Networking support --->        [CONFIG_NET]
      Networking options --->
        <*> Packet socket          [CONFIG_PACKET]
        <*> The IPv6 Protocol ---> [CONFIG_IPV6]

Installation of ISC DHCP

[Note]

Note

This package does not support parallel build.

[Note]

Note

Be careful with the instructions below. The single and double quotes are important because the defined variables are used verbatim in the code.

Install ISC DHCP by running the following commands:

( export CFLAGS="$CFLAGS -Wall -fno-strict-aliasing                 \
        -D_PATH_DHCLIENT_SCRIPT='\"/sbin/dhclient-script\"'         \
        -D_PATH_DHCPD_CONF='\"/etc/dhcp/dhcpd.conf\"'               \
        -D_PATH_DHCLIENT_CONF='\"/etc/dhcp/dhclient.conf\"'"        &&

./configure --prefix=/usr                                           \
            --sysconfdir=/etc/dhcp                                  \
            --localstatedir=/var                                    \
            --with-srv-lease-file=/var/lib/dhcpd/dhcpd.leases       \
            --with-srv6-lease-file=/var/lib/dhcpd/dhcpd6.leases     \
            --with-cli-lease-file=/var/lib/dhclient/dhclient.leases \
            --with-cli6-lease-file=/var/lib/dhclient/dhclient6.leases
) &&
make -j1

This package does not come with a test suite.

If you only want to install the ISC DHCP client, issue the following commands as the root user:

make -C client install         &&
mv -v /usr/sbin/dhclient /sbin &&
install -v -m755 client/scripts/linux /sbin/dhclient-script

Skip to the section called “Client Configuration” in order to configure the client

If you only want to install the ISC DHCP server, issue the following command as the root user:

make -C server install

Skip to the section called “Server Configuration” in order to configure the server.

Alternatively, you can install whole package which includes the client, server, relay, static libraries and development headers by running the following commands as the root user:

make install                   &&
mv -v /usr/sbin/dhclient /sbin &&
install -v -m755 client/scripts/linux /sbin/dhclient-script

Configuring ISC DHCP

Config Files

/etc/dhcp/dhclient.conf and /etc/dhcp/dhcpd.conf

Client Configuration

Create a basic /etc/dhcp/dhclient.conf by running the following command as the root user:

install -vdm755 /etc/dhcp &&
cat > /etc/dhcp/dhclient.conf << "EOF"
# Begin /etc/dhcp/dhclient.conf
#
# Basic dhclient.conf(5)

#prepend domain-name-servers 127.0.0.1;
request subnet-mask, broadcast-address, time-offset, routers,
        domain-name, domain-name-servers, domain-search, host-name,
        netbios-name-servers, netbios-scope, interface-mtu,
        ntp-servers;
require subnet-mask, domain-name-servers;
#timeout 60;
#retry 60;
#reboot 10;
#select-timeout 5;
#initial-interval 2;

# End /etc/dhcp/dhclient.conf
EOF

See man 5 dhclient.conf for additional options.

Now create the /var/lib/dhclient directory which will contain DHCP Client leases by running the following command as the root user:

install -v -dm 755 /var/lib/dhclient

If you want to configure network interfaces at boot using dhclient, you need to install the dhclient@.service unit included in the blfs-systemd-units-20191026 package by running the following command as the root user:

make install-dhclient
[Note]

Note

Make sure that you disable the systemd-networkd service or configure it not to manage the interfaces you want to manage with dhclient.

At this point you can test if dhclient is behaving as expected by running the following command as the root user:

systemctl start dhclient@eth0

To start dhclient on a specific interface at boot, enable the previously installed systemd unit by running the following command as the root user:

systemctl enable dhclient@eth0

Replace eth0 with the actual interface name.

Server Configuration

Note that you only need the DHCP server if you want to issue LAN addresses over your network. The DHCP client doesn't need the server in order to function properly.

Start with creating /etc/dhcp/dhcpd.conf by running the following command as the root user:

cat > /etc/dhcp/dhcpd.conf << "EOF"
# Begin /etc/dhcp/dhcpd.conf
#
# Example dhcpd.conf(5)

# Use this to enable / disable dynamic dns updates globally.
ddns-update-style none;

# option definitions common to all supported networks...
option domain-name "example.org";
option domain-name-servers ns1.example.org, ns2.example.org;

default-lease-time 600;
max-lease-time 7200;

# This is a very basic subnet declaration.
subnet 10.254.239.0 netmask 255.255.255.224 {
  range 10.254.239.10 10.254.239.20;
  option routers rtr-239-0-1.example.org, rtr-239-0-2.example.org;
}

# End /etc/dhcp/dhcpd.conf
EOF

Adjust the file to suit your needs. See man 5 dhcpd.conf for additional options.

Now create the /var/lib/dhcpd directory which will contain DHCP Server leases by running the following command as the root user:

install -v -dm 755 /var/lib/dhcpd

If you want to start the DHCP Server at boot, install the dhcpd.service unit included in the blfs-systemd-units-20191026 package:

make install-dhcpd

You will need to edit the /etc/default/dhcpd in order to set the interface on which dhcpd will serve the DHCP requests.

Contents

Installed Programs: dhclient, dhclient-script, dhcpd, dhcrelay and omshell
Installed Libraries: libdhcpctl.a and libomapi.a
Installed Directories: /etc/dhcp, /usr/include/dhcpctl, /usr/include/isc-dhcp, /usr/include/omapip, /var/lib/dhclient and /var/lib/dhcpd

Short Descriptions

dhclient

is the implementation of the DHCP client.

dhclient-script

is used by dhclient to (re)configure interfaces. It can make extra changes by invoking custom dhclient-{entry,exit}-hooks.

dhcpd

implements Dynamic Host Configuration Protocol (DHCP) and Internet Bootstrap Protocol (BOOTP) requests for network addresses.

dhcrelay

provides a means to accept DHCP and BOOTP requests on a subnet without a DHCP server and relay them to a DHCP server on another subnet.

omshell

provides an interactive way to connect to, query and possibly change the ISC DHCP Server's state via OMAPI, the Object Management API.

Last updated on 2020-02-21 09:11:06 -0800